Cook Hinged Base Manuel d'utilisateur télécharger pdf

LEFT SIDE OF BASE

RIGHT SIDE OF BASE

BOTTOM EDGE

OF BASE

BOTTOM EDGE

OF BASE

(TEMPLATE)

11/32

7/16

3/8

11/32

7/16

Hinged Base

SUPPLEMENTAL INSTALLATION INSTRUCTIONS

Verify that all of the following parts have been shipped:

Part Name Number of Parts

• Curb Latch Plate . . . . . . . . . . . . . . . . . . . . . 1

• Hinge Plates (1 Left 1 Right). . . . . . . . . . . . 2

• Aircraft Cable (72”) . . . . . . . . . . . . . . . . . . . 1

• Cable Clamps . . . . . . . . . . . . . . . . . . . . . . . 2

• Bolts 5/16 x 1 1/2 . . . . . . . . . . . . . . . . . . . 2

• Bolt 5/16 x 3/4 . . . . . . . . . . . . . . . . . . . . . . 1

(to secure latch in closed position)

• Nut 5/16 . . . . . . . . . . . . . . . . . . . . . . . . . . 1

(to secure latch in closed position)

• 1/4 x 3/4 Kwik Drill screws . . . . . . . . . . . . . 8

• Wood Screws 1 1/2” . . . . . . . . . . . . . . . . . 16

• Pop rivets (retroﬁt only). . . . . . . . . . . . . . . . 2

• Base Latch Plate (retroﬁt only) . . . . . . . . . . 1

Place the hinge plates on the curb as shown. The edge of

the hinge plate should be ﬂush with the edge of the curb.

The 1/2” tapped rod should extend past the edge of the curb

approximately 3/8”. Before fastening the second hinge plate,

verify that the distance between the left tapped rod and the

right tapped rod is approximately 1/4” less than the inside

dimension of the base. Secure in place with the wood

screws provided.

Standard Installation:

• Place fan on curb with hinge holes in base aligned with

tapped rod on hinge plate.

Retroﬁt Installation Below:

• Drill 3/8” diameter hole through base, on the left and right

side of base as shown below.

Insert 5/16 x 1 1/2” bolt through hole in base and thread into

tapped rod on hinge plate.

Insert 5/16 x 1 1/2” bolt through hole on opposite side in base

and thread into tapped rod on hinge plate.

Tighten both bolts until the shank of the bolts bottom out in the

threaded rod.

Standard Installation:

• Lift fan up far enough to get the curb latch plate into position.

• Align the left hole of the curb latch plate with the slot on the

right of the base latch plate.

• Secure the curb latch plate with the wood screws provided.

Retroﬁt Installation:

• Center the base latch plate on side of base as shown.

• Mark location of holes on housing base using the latch plate

as a template.

• Drill 7/32” diameter holes through base using the template.

(Below)

• Secure base latch plate to base using pop rivets provided.

Pop rivets should be inserted from inside the base through

the latch plate.

• Lift fan up far enough to get the curb latch plate into position.

• Align the left hole of the curb latch plate with the slot on the

right of the base latch plate.

• Secure the base latch plate with the wood screws provided

Assemble the aircraft cable and clamps as shown. The cable

length should allow the fan to pivot just past the balance point.

If cable does not allow fan to pivot far enough to stay open,

loosen one cable clamp and adjust cable length as necessary.

1 2

Hinged Base 1
Hinge Side 2

Résumé du contenu

Page 1 - Hinged Base

1 LEFT SIDE OF BASERIGHT SIDE OF BASEBOTTOM EDGEOF BASEBOTTOM EDGEOF BASE(TEMPLATE)11/327/163/83/811/327/16 Hinged Base SUPPLEMENTAL INSTALLATION INS

Page 2 - Hinge Side

2 1/8" Pop RivetHead on Insideof Base1/4" Kwik DrillSheetmetal Screw (3)1/4" Kwik DrillSheetmetal Screw (2) 1-1/2" Wood ScrewHing

Commentaires sur ces manuels

Pas de commentaire

Cook Hinged Base Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Cuisine Cook Hinged Base. COOK Hinged Base User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Cuisine Cook Hinged Base