Cook CF-4 Manuel d'utilisateur télécharger pdf (Page 1)

Swing Out Centrifugal Blowers

SUPPLEMENTAL INSTALLATION INSTRUCTIONS

CA-4/CF-4

This publication contains the supplemental installa-

tion instructions for standard units of the

CA-4/CF-4-

Swing Out Centrifugal Blowers

. Carefully read this

publication, as well as the CA/CF/CP Installation, Oper-

ation, and Maintenance manual, prior to any installa-

tion or maintenance procedure.

Loren Cook catalog,

CA and CF,

provides additional

information describing the equipment, fan performance,

available accessories, and speciﬁcation data.

For additional safety information, refer to AMCA publica-

tion 410-96,

Safety Practices for Users and Installers of

Industrial and Commercial Fans

All of the publications listed above can be obtained from

Loren Cook Company by phoning 417/869-6474, extension

166; by FAX at 417/832-9431; or by e-mail at info@loren-

cook.com.

For information on special equipment, contact Loren

Cook Company Customer Service Department at 417/869-

6474.

Swing Out Door

All moving parts that require maintenance are mounted

on a hinged door that opens to provide easy access.

• Disconnect power to the unit.

• Clear area around door to allow it to swing open.

• Remove locking pin(s) from door (door latches may

have to be loosened slightly).

• Loosen restraining bolts located at the top and bottom

of door.

• Loosen and remove door latches in steps to insure

even opening of door.

• Pull door open.

• Reverse the steps above to close door.

CA-4 Swing Out

Part No.

Description

Sizes 210-490

etalP rotoM1

gnisuoH2

niP gnikcoL rooD3

eldnaH hctaL rooD4

gniraeB draobnI5

gniraeB draobtuO6

tfahS7

8 Bearing Support/Door Assembly

leehW9

Parts Not Sh own: Motor, Motor Sheave, Inlet Cone, Fan Sheave, Belt Set

Parts List

Front View

Drive Side View

The correct wheel-to-inlet clearance is critical to proper

fan performance. This clearance should be verified

before initial start-up since rough handling during

shipment could cause a shift in fan components. Refer

to wheel/inlet drawing for correct overlap.

Adjust the overlap by loosening the wheel hub and

moving the wheel along the shaft to obtain the correct

value.

A uniform radial gap

(space between the

edge of the cone and

the edge of the inlet) is

obtained by loosening

the inlet cone bolts and

repositioning the inlet

cone.

Size Overlap

210-245 1/4”

270-300 5/16”

330-365 3/8”

402 7/16”

445-490 1/2”

CA-4/CF-4

IOM Dec 2013

CA-4/CF-4 1

Résumé du contenu

Page 1 - CA-4/CF-4

1 Swing Out Centrifugal Blowers SUPPLEMENTAL INSTALLATION INSTRUCTIONS CA-4/CF-4 This publication contains the supplemental installa-tion instructio

Modèles reliés CA-4

Commentaires sur ces manuels

Pas de commentaire

Cook CF-4 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Cuisine Cook CF-4. COOK CF-4 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés CA-4

Commentaires sur ces manuels

Cook CF-4 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Cuisine Cook CF-4. COOK CF-4 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés CA-4

Commentaires sur ces manuels

Produits connexes et manuels pour Cuisine Cook CF-4